we never had so much possibilities
No more headache,
No more need to change the power supply because we didn’t have enough outputs,
Let’s finally discover the true power of modularity!
With the FX Teacher, FX Power Source,
We finally have the possibility of increasing the number of outputs of its power supply unit unlimitedly!
concretely, how it works?
When you receive your kit you will have 4 supply boards.
Each of them offers 2 power supply outputs.
So you will have a total of 8 outputs when you begin.
You can then add as many boards as you need, for a small fee,
and with up to 60x 9V outputs! And of course… We challenge you to do it!
we never had
so much possibilities
No more headache,
No more need to change the power supply because
we didn’t have enough outputs,
Let’s finally discover the true power of modularity!
With the FX Teacher, FX Power Source,
We finally have the possibility of increasing the number
of outputs of its power supply unit unlimitedly!
concretely,
how it works?
When you receive your kit you will have 4 supply boards.
Each of them offers 2 power supply outputs.
So you will have a total of 8 outputs when you begin.
You can then add as many boards as you need,
for a small price, and up to 60x 9V outputs!
Of course… We challenge you to do it if you can!
a customised supply voltage
Thanks to our modular system,
You can easily choose your output voltage.
Choose between 9V, 12V or 18V for each board when you order them.
Then assemble them following our instructions in the assembly article.
And our adaptors are compatible with all the countries with 110-230V @50-60 cycles.
We also supply when you order the compatible IEC plug for your country.
compatible with most of the pedals
The kit comes with a set of 5.5×2.1mm jacks.
They will power most effect pedals on the market!
And of course, we have provided all sizes, from 25cm to 90cm.
There is even a reversed polarity cable for positive centre pedals.
However, there is no positive ground for our power supply, these pedals will work better on batteries.
compatible with every pedalboards
We have tried several brands of pedalboards, such as Pedaltrain, Aclam, Temple Audio, etc…
We have designed our brackets so that they are compatible with ALL pedalboards!
On a Pedaltrain, simply mark, drill and screw.
For a Temple Audio, we have planned the location of their screw system.
For all the others, self-drilling screws are provided to simply install right into the metal!
And there is a step by step tutorial to lean how to mount your brackets on any pedalboards!
a customised
supply voltage
Thanks to our modular system,
You can easily choose your output voltage.
Choose between 9V, 12V or 18V
for each board when you order.
Then assemble them following our instructions
in the assembly article.
compatible with most of the pedals
and pedalboards
The kit comes with a set of 5.5×2.1mm jacks.
And of course, we have provided all sizes,
from 25cm to 90cm.
There is even a reversed polarity cable
for positive centered pedals.
However, there is no positive ground
possibility for our power supply,
these pedals will work better on batteries.
We have tried several brands of pedalboards, such as Pedaltrain, Aclam, Temple Audio, etc…
We have designed our brackets so that they are compatible with ALL pedalboards!
fans of performance
This new power supply unit delivers enough power for 90% of the pedals on the market!
With its 200mA per electronic board, you can, if necessary, put a Y-cable to double the current.
But for traditional pedals it is more than enough…
If you’re looking for something stronger, the Anasounds K+, is your solution.
We’ve found a switching technology capable of delivering 2A per output!
a breathtaking silence
Thanks to our technology, the 60 cycle and its harmonics will not be invited.
Just load the power supply and measure, our filters won’t let anything go through!
Thanks to our technology, we filter these frequencies much more efficiently than a traditional transformer system.
For example with this 1kHz signal injected in 8 true bypass in series.
No harmonics or high frequencies disturbed the line due to a power supply problem.
compatible with anasounds k+ power source
Our first concept is to take the 60 cycle out of the power supply unit using a 24V DC power supply.
This is the same power supply as for our Anasounds K+ Power Source.
By using the 24V thru, one unit can power the other with a simple jack cable!
You can therefore use the Anasounds power supply for big currents then,
The FX Teacher for less powerful pedals…
a tested electronic insulation
We pay a lot of attention to the quality of our products.
This is why a division of the R&D team has dedicated 2 years for this project,
And has tested almost all the possibilities and the technologies offered by this market.
We undestand that taking the transformer out and our technology can create ground loops.
But that elimination of the 60 cycle and the implementation of this electronic insulation and,
This ultra powerful filtering finally offers performances higher than a traditional block!
This blog article details more about the technology and in which situation one block or another is recommended.
Read it, it’s very informative!
Moreover, this rather simple but very effective technology is one of the only ones that can be used in DIY!
So take advantage of it, for the rest of the technologies, we move on to miniaturised components or lethal voltages.
fans of performance
This new power supply unit delivers enough power
for 90% of the pedals on the market!
With its 200mA per electronic board,
you can, if necessary,
put a Y-cable to double the current.
But for traditional pedals it is more than enough…
If you’re looking for something stronger,
the Anasounds K+, has the answer.
We’ve found a switching technology
capable of delivering up to 2A per output!
a breathtaking silence
Thanks to our technology, the 50Hz and its harmonics
will not be invited.
Just charge the power supply and measure,
our filters won’t let anything go through!
Thanks to our technology, we filter these frequencies
much more efficiently than a traditional transformer system.
compatible with the
anasounds k+ power source
Our first concept is to take the 50Hz out of the
power supply unit using a 24V DC power supply.
This is the same power supply as for our
Anasounds K+ Power Source.
By using the 24V thru, one unit can power
the other, with a simple jack cable!
You can therefore use the Anasounds
power supply for big currents,
then, the FX Teacher for less powerful pedals…
a tested electronic insulation
We pay a lot of attention to,
the quality of our products.
This is why a division of the R&D team
has dedicated 2 years for this project,
and has tested almost all the possibilities
and the technologies offered in this market.
We realise that taking the transformer out
and our technology used
can creates ground loops.
But that the elimination of the 60 cycle and the implementation of this electronic insulation,
plus this ultra powerful filtering finally offers
performances higher than a traditional block!
This blog article details more
about the technology and in which situation
one block or another is recommended.
Read it, it’s very informative!
what if i told you you’re able to put a pedal together?
Almost all of us know that familiar frustration of putting together a kit and realising it doesn’t work.
You’ve tried everything yet you don’t understand what the problem is.
This is how FX Teacher came about, with the promise to give you all the instructions and the tools to get you building!
With a little patience and know-how, you will be the master and creator of your effects.
Isn’t that great?
Here’s what we offer to help you along the way:
Learn the basis of electronics and DIY thanks to our blog articles.
It’s all free and easy to access.
We have devised a fool-proof building method.
If you still can’t figure it out you’re just trying to make us mad!
We have a selection of tools at your disposal.
This way, you won’t have to waste your time finding the right reference on a multitude of websites.
We even use some of those tools for our own production.
And they are under warranty from our French supplier.
Each kit has been designed exactly like an Anasounds pedal.
Quality components, carefully selected and thought out.
You should enjoy many years with a great sound!
To make it visually compatible with the Anasounds swag you’re used to,
you don’t have to buy tools to get the box ready.
We supply it with our designs. Pretty cool, right?
We’re doing DIY masterclasses!
The idea is to spend a day together and build your own pedal.
Wanna attend a masterclass? There you go!
Disclaimer: Anasounds and FX Teacher are not associated with or endorsed by the creators or brands of
the pedals cited or used in the design and/or creation of these effect pedals.
Anasounds and FX Teacher are not responsible for the use and assembly of your kits.
A soldering iron heats, burns, be careful. The use of high voltages is prohibited!
The use of chemicals and toxic products is dangerous, do not ingest.
Also be careful when buying a second hand pedal, the serial numbers
starting by “D” on the certificate are not manufactured by our team. They are not under warranty.
FX Teacher brand DIY products will be mounted under supervision and monitoring,
of their owner. Pay attention to the currents, voltages used and the risks involved.
If you need help, leave a comment in the FX Teacher blog’s assembly article.
